hp-concentra-wrapper-portlet Actions Blinking Lights The following sections describe the most common combinations of blinking flashing lights displayed on the control panel, followed by solutions for each combination. Find the blinking lights pattern you are experiencing, and then follow the steps to resolve the issue. Figure Control panel with lights indicated Power light Attention light Check color cartridge light Check black cartridge light Issue All the lights are blinking In this error condition, all of the control panel lights are blinking Power light Blinking Attention light Blinking Check color cartridge light Blinking Check black cartridge light Blinking Figure Control panel with the lights indicated Cause The product is in an error state. Solutions Solution one Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution two Plug the All-in-One directly into an electrical outlet Plug the product directly into an electrical outlet to make sure that the power source functions correctly. Disconnect the power cord from the rear of the product. Unplug the power cord from any power strips or surge suppressors. Plug the power cord directly into an electrical outlet. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Try the task again. If the issue persists, try a different electrical outlet. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution three Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue One or both Check Cartridge lights are on In this error condition, the following control panel light pattern displays Power light On Attention light Off Check color cartridge light On or off Check black cartridge light On or off Figure Control panel with both check cartridge lights blinking Figure Control panel with one check cartridge light blinking If both check cartridge lights are on, there is an issue with both cartridges. If the left check cartridge light is on, there is an issue with the tri-color cartridge. If the right check cartridge light is on, there is an issue with the black cartridge. Cause The indicated cartridge is low on ink. Solutions If one or both of the cartridges is low on ink, you do not need to replace the cartridges yet, unless you are dissatisfied with the print quality. Solution one Check the ink levels Follow these steps to check the ink levels. Open the HP product software Windows XP Click Start , click All Programs, click HP, click the folder for your HP product, and then click the icon for your HP product . Windows Vista Click the Windows icon , click Programs, click HP, click the folder for your HP product, and then click the icon for your HP product . Windows 7 Click the Windows icon , click All Programs, click HP, click the folder for your HP product, and then click the icon for your HP product . note You can also open the HP product software from your computer desktop by double-clicking the icon for your HP product . The product software opens. In the product software, double-click Estimated Ink Levels . The HP Toolbox opens a graphic that shows the estimated ink levels for your product. Figure The estimated ink levels graphic If the estimated ink levels are low, and you are satisfied with the quality of your printouts, ignore the lights until you are dissatisfied with the printouts. If the estimated ink levels are low, and you are dissatisfied with the quality of your printouts, replace the cartridges. Continue to the next solution. Solution two Replace the problem cartridge Follow these steps in the order given to replace the cartridges. Step one Replace the cartridge Purchase replacement cartridges and other supplies from the HP Store or local retailers. Press the Power button to turn on the product. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Lightly press down on the cartridge to release it, and then pull the cartridge out to remove it from its slot. Figure Remove the cartridge caution Do not touch the copper-colored contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections. Figure Do not touch the contacts or nozzles Remove the new cartridge from its packaging, and then pull the pink pull tab to remove the plastic tape. caution Do not touch the copper-colored contacts or ink nozzles. Also, do not retape the cartridges. Doing so can result in clogs, ink failure, and bad electrical connections. Figure Remove the plastic tape Hold the cartridge by its sides with the nozzles toward the product, and then insert the cartridge into its slot. Make sure that the icon on the cartridge matches the icon on the slot. The tri-color cartridge goes in the slot on the left The black cartridge goes in the slot on the right Figure Insert the cartridge into its slot Push the cartridge forward into its slot until it snaps into place. Repeat these steps to replace the other cartridge, if necessary. Close the cartridge access door. Figure Close the cartridge access door Press the button next to OK on the control panel display . The product prints an alignment page. Step two Align the cartridges Lift the scanner lid. Place the alignment page with the printed-side down on the right-front corner of the scanner glass. See the engraved guide next to the scanner glass for help loading the alignment page. Figure Place the alignment page on the scanner glass Close the scanner lid. Press the button next to OK on the control panel display . The product scans the alignment page. When the Alignment successful message displays on the control panel screen, press the button next to OK on the control panel display to complete the alignment. Step three Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Setup Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution three Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue One or both Check Cartridge lights are blinking In this error condition, the following control panel light pattern displays Power light On Attention light Off Check color cartridge light Blinking or off Check black cartridge light Blinking or off Figure Control panel with lights indicated Figure Control panel with lights indicated If both check cartridge lights are blinking, there is an issue with both cartridges. If the left check cartridge light is blinking, there is an issue with the tri-color cartridge. If the right check cartridge light is blinking, there is an issue with the black cartridge. Causes One or both cartridges are incompatible with the product. One or both cartridges are defective. One or both cartridges still have the protective tape on the nozzles. A problem has occurred with one or both cartridges. Solutions Solution one Check the cartridge compatibility Follow these steps to make sure that the cartridges are compatible with your product. Purchase replacement cartridges and other supplies from the HP Store or local retailers. Press the Power button to turn on the product, if the power is not already on. Open the cartridge access door. The carriage moves to the center of the product. Wait until the product is idle and silent before proceeding. Find the number on the label on the top of each cartridge. Figure Number on the cartridge label Cartridge numbers Make a note of the cartridge number printed on the label of each cartridge, and then close the cartridge access door. Refer to the list of cartridge numbers in the HP Sure Supply window. If either of the cartridge numbers is not in the list, replace the cartridge with a new one that is in the list. For instructions on how to replace the cartridges, skip to the solution to replace the cartridges. Solution two Resolve the cartridge problem Follow these steps in the order given to resolve the cartridge problem. Step one Clean the problem cartridge contacts Follow these steps in the order given to clean the electrical contacts. note If both cartridge lights are blinking, complete the steps for both cartridges. Gather the following items Distilled water. Use bottled or filtered water if distilled water is not available. Clean cotton swabs or any soft, lint-free material that will not stick to the cartridges coffee filters work well. Open the cartridge access door. The carriage moves into the center of the access area, unless there is an obstruction. Figure Open the cartridge access door Figure The carriage in the center of the product Disconnect the power cord from the rear of the product. Press down on one of the cartridges to release it, and then pull it out from its slot. Figure Remove the cartridge caution Do not touch the copper-colored contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections. Figure Do not touch the contacts or nozzles If protective tape is still on the cartridge, remove it. Do not remove the copper-colored strip. Figure Remove the protective tape If you removed the protective tape from the cartridge, there is no need to clean the cartridge. Continue to the step to reinstall the cartridge. Place the cartridge on a piece of paper with the nozzle plate facing up. Dip a cotton swab into the clean distilled water, and then squeeze it to remove most of the moisture. The swab should be only slightly damp. Clean the cartridge contacts. caution Avoid touching the nozzles. Figure Clean the cartridge contacts note Clean the contacts quickly so that the cartridge is not outside the product for more than 30 minutes. The ink can dry and clog the nozzles if the cartridge is outside of the product for too long. Clean the contacts in the carriage for the problem cartridge. warning Make sure that the power cord is disconnected from the product. Figure Carriage Figure The gold-colored contacts in the carriage Wait ten minutes to allow the cartridge and carriage to dry. Place the cartridge in its slot at a slightly upward angle, and then press up and forward until the cartridge snaps into position. The tri-color cartridge goes in the slot on the left. The black cartridge goes in the slot on the right. Figure Insert the cartridge into its slot Reconnect the power cord to the rear of the product. Close the cartridge access door. Figure Close the cartridge access door Press the button next to OK on the control panel display . The product prints an alignment page. Step two Align the cartridges Lift the scanner lid. Place the alignment page with the printed-side down on the right-front corner of the scanner glass. See the engraved guide next to the scanner glass for help loading the alignment page. Figure Place the alignment page on the scanner glass Close the scanner lid. Press the button next to OK on the control panel display . The product scans the alignment page. When the Alignment successful message displays on the control panel screen, press the button next to OK on the control panel display to complete the alignment. Step three Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, there is no need to continue troubleshooting. If the issue persists, see the next step. Step four Replace the problem cartridge Purchase replacement cartridges and other supplies from the HP Store or local retailers. Press the Power button to turn on the product. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Lightly press down on the cartridge to release it, and then pull the cartridge out to remove it from its slot. Figure Remove the cartridge caution Do not touch the copper-colored contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections. Figure Do not touch the contacts or nozzles Remove the new cartridge from its packaging, and then pull the pink pull tab to remove the protective plastic tape. caution Do not touch the copper-colored contacts or ink nozzles. Also, do not retape the cartridges. Doing so can result in clogs, ink failure, and bad electrical connections. Figure Remove the protective plastic tape Hold the cartridge by its sides with the nozzles toward the product, and then insert the cartridge into its slot. Make sure that the icon on the cartridge matches the icon on the slot. The tri-color cartridge goes in the slot on the left. The black cartridge goes in the slot on the right. Figure Insert the cartridge into its slot Push the cartridge forward into its slot until it snaps into place. Repeat these steps to replace the other cartridge, if necessary. Close the cartridge access door. Figure Close the cartridge access door Press the button next to OK on the control panel display . The product prints an alignment page. Step five Align the cartridges Lift the scanner lid. Place the alignment page with the printed-side down on the right-front corner of the scanner glass. See the engraved guide next to the scanner glass for help loading the alignment page. Figure Place the alignment page on the scanner glass Close the scanner lid. Press the button next to OK on the control panel display . The product scans the alignment page. When the Alignment successful message displays on the control panel screen, press the button next to OK on the control panel display to complete the alignment. Step six Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution three Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue Both Check Cartridge lights and the Attention light are blinking In this error condition, the following control panel light pattern displays Power light On Attention light Blinking fast Check color cartridge light Blinking fast Check black cartridge light Blinking fast Figure Control panel with lights indicated Cause The carriage inside the product stalled. Solutions Solution one Clear any jammed paper Jammed paper can cause the carriage to stall. Follow these steps to clear any jammed paper. Experiencing frequent or recurring paper jams? Preventing paper jams The following recommendations can help prevent recurring paper jams in your HP product. Before loading paper in the tray, hold the stack of paper, and then tap the bottom edge on a flat surface so that the stack is even on all sides. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. caution Do not force the paper to move too far forward in the tray. Do not overload the tray with paper. Only add paper to the tray when the product is not printing. Make sure the HP product supports the paper type. See the documentation that came with the HP product for more information. Do not print on paper with paper clips or staples attached. Do not use paper that is bent, torn, dusty, damp, wrinkled, curled, or paper that does not lie flat. Use only one type of paper at a time. Do not mix different types, weights, or sizes of paper. Do not use paper that is too thin, too thick, or too glossy for the product. Causes of paper jams The following factors can cause paper jams Paper loaded incorrectly in the paper tray. Damaged or dirty paper rollers. Torn, wrinkled, or damp paper loaded in the paper tray. The rear access door or two-sided printing accessory duplexer might not be closed or is not locked into place. Paper was added to a stack already in the tray while the HP product was printing. The tray contains more than one type of paper. The paper is jammed inside the HP product where you cannot see it. An obstruction is blocking the paper path. Torn pieces of paper from a previous jam are stuck in the product. The tray is too full. If printing on an envelope, the edges of the envelope are bent. Step one Remove any loose paper Remove any loose sheets of paper from the input tray and the output tray. caution Do not remove jammed paper at this stage. Trying to clear jammed paper from the front of the product can damage theprint mechanism. Remove any loose paper Do not pull jammed paper Step two Clear the paper jam from the base of the All-in-One Use the following steps to check for and then remove jammed paper from the base of the HP product. Press the Power button to turn off the product. Disconnect the USB cable from the back of the product. Disconnect the power cord from the back of the product. Turn the product so that you can access its underside base. Press in the tabs on either side of the cleanout door to open it. Figure Open the cleanout door on the base of the product Gently remove any jammed paper from inside the product. Figure Remove jammed paper from inside the product caution If the paper tears while removing it, check inside the door for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. Reattach the cleanout door. Gently push the door forward until it snaps into place. Figure Reattach the cleanout door Reconnect the power cord to the back of the product. Press the Power button to turn on the product. Step three Clear the jam from inside the All-in-One Press the Power button to turn off the product. Disconnect the power cord from the rear of the product. Open the cartridge access door. Figure Open the cartridge access door Gently remove any paper that is jammed inside the product. Figure Remove jammed paper from inside the product Close the cartridge access door. Figure Close the cartridge access door Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step four Clear the jam from the front of the All-in-One If you cannot remove the jam from the base or inside the product, follow these steps to remove the paper jam from the front. Press the Power button to turn off the product. Disconnect the power cord from the rear of the product. Grasp the jammed paper with both hands, and then slowly pull it from the front of the product. Figure Remove jammed paper from the front of the product note If the paper tears while removing it, check for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step five Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step six Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution two Make sure that the carriage moves freely Follow these steps in the order given to make sure that the carriage moves freely. Step one Make sure that the carriage moves freely Follow these steps to make sure that the carriage can move freely. Press the Power button to turn on the product. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Without turning off the product, disconnect the power cord from the rear of the product. warning You must unplug the power cord to allow you to move the carriage by hand and to reset the paper feed mechanism without the risk of an electrical shock. Look inside the product to see where the carriage is stuck, and then check for any torn paper or other objects that might be restricting the carriage. You might need a flashlight to illuminate areas for proper viewing. caution If the paper tears when you remove it from the rollers, check the rollers and wheels for torn pieces of paper that might remain inside the product. If pieces of paper remain in the product, more paper jams might occur. Remove any loose paper or obstructions found. Reach inside the product through the cartridge access door, and then manually move the carriage. If the carriage is stuck on the right side of the product, move the carriage to the left side of the product. If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Make sure that the carriage can move freely across the width of the product. Firmly push the carriage to the left side of the product, and then to the right side. Close the cartridge access door. Figure Close the cartridge access door Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution three Remove and then reinstall the cartridges Improper placement or installation of the cartridges can cause the product to indicate a carriage jam error. Follow these steps to remove and then reinstall the cartridges. Step one Remove the cartridges Press the Power button to turn on the product, if the power is not already on. Wait until the product is idle and silent before proceeding. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Lightly press down on the cartridge to release it, and then pull the cartridge out to remove it from its slot. Figure Remove the cartridge caution Do not touch the copper-colored electrical contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections. Figure Do not touch the contacts or nozzles Check for obstructions under and around the carriage. Clear any obstructions that you find. You might need a flashlight to illuminate areas for proper viewing. Step two Reinstall the cartridges Follow these steps to reinstall the cartridges. Repeat the steps for each cartridge. Hold the cartridge by its sides with the nozzles toward the product, and then insert the cartridge into its slot. Make sure that the icon on the cartridge matches the icon on the slot. The tri-color cartridge goes in the slot on the left. The black cartridge goes in the slot on the right. Figure Insert the cartridge into its slot Push the cartridge forward into its slot until it snaps into place. Figure Snap the cartridge into place Repeat these steps to remove and then reinstall the other cartridge. Close the cartridge access door. Figure Close the cartridge access door Press the Power button to turn on the product. Step three Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution four Plug the All-in-One directly into an electrical outlet Plug the product directly into an electrical outlet to make sure that the power source functions correctly. Disconnect the power cord from the rear of the product. Unplug the power cord from any power strips or surge suppressors. Plug the power cord directly into an electrical outlet. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Try the task again. If the issue persists, try a different electrical outlet. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution five Perform a power reset Follow these steps to reset the product. Step one Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution six Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue Both Check Cartridge lights and the Power light are blinking fast In this error condition, the following control panel light pattern displays Power light Blinking fast Attention light On Check color cartridge light Blinking fast Check black cartridge light Blinking fast Figure Control panel with lights indicated Causes The cartridge access door is open. The carriage is jammed. Solutions Solution one Close the cartridge access door Close the cartridge access door. Figure Close the cartridge access door Check the product control panel for the blinking lights. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution two Clear any jammed paper Jammed paper can cause the carriage to stall. Follow these steps to clear any jammed paper. Experiencing frequent or recurring paper jams? Preventing paper jams The following recommendations can help prevent recurring paper jams in your HP product. Before loading paper in the tray, hold the stack of paper, and then tap the bottom edge on a flat surface so that the stack is even on all sides. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. caution Do not force the paper to move too far forward in the tray. Do not overload the tray with paper. Only add paper to the tray when the product is not printing. Make sure the HP product supports the paper type. See the documentation that came with the HP product for more information. Do not print on paper with paper clips or staples attached. Do not use paper that is bent, torn, dusty, damp, wrinkled, curled, or paper that does not lie flat. Use only one type of paper at a time. Do not mix different types, weights, or sizes of paper. Do not use paper that is too thin, too thick, or too glossy for the product. Causes of paper jams The following factors can cause paper jams Paper loaded incorrectly in the paper tray. Damaged or dirty paper rollers. Torn, wrinkled, or damp paper loaded in the paper tray. The rear access door or two-sided printing accessory duplexer might not be closed or is not locked into place. Paper was added to a stack already in the tray while the HP product was printing. The tray contains more than one type of paper. The paper is jammed inside the HP product where you cannot see it. An obstruction is blocking the paper path. Torn pieces of paper from a previous jam are stuck in the product. The tray is too full. If printing on an envelope, the edges of the envelope are bent. Step one Remove any loose paper Remove any loose sheets of paper from the input tray and the output tray. caution Do not remove jammed paper at this stage. Trying to clear jammed paper from the front of the product can damage theprint mechanism. Remove any loose paper Do not pull jammed paper Step two Clear the paper jam from the base of the All-in-One Use the following steps to check for and remove jammed paper from the base of the HP product. Press the Power button to turn off the product. Disconnect the USB cable from the back of the product. Disconnect the power cord from the back of the product. Turn the product so that you can access its underside base. Press in the tabs on either side of the cleanout door to open it. Figure Open the cleanout door on the base of the product Gently remove any jammed paper from inside the product. Figure Remove jammed paper from inside the product caution If the paper tears while removing it, check inside the door for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. Reattach the cleanout door. Gently push the door forward until it snaps into place. Figure Reattach the cleanout door Reconnect the power cord to the back of the product. Press the Power button to turn on the product. Step three Clear the jam from inside the All-in-One Press the Power button to turn off the product. Disconnect the power cord from the rear of the product. Open the cartridge access door. Figure Open the cartridge access door Gently remove any paper that is jammed inside the product. Figure Remove jammed paper from inside the product Close the cartridge access door. Figure Close the cartridge access door Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step four Clear the jam from the front of the All-in-One If you cannot remove the jam from the base or inside the product, follow these steps to remove the paper jam from the front. Press the Power button to turn off the product. Disconnect the power cord from the rear of the product. Grasp the jammed paper with both hands, and then slowly pull it from the front of the product. Figure Remove jammed paper from the front of the product note If the paper tears while removing it, check for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step five Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step six Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution three Make sure that the carriage moves freely Follow these steps in the order given to make sure that the carriage moves freely. Step one Make sure that the carriage moves freely Follow these steps to make sure that the carriage can move freely. Press the Power button to turn on the product. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Without turning off the product, disconnect the power cord from the rear of the product. warning You must unplug the power cord to allow you to move the carriage by hand and to reset the paper feed mechanism without the risk of an electrical shock. Look inside the product to see where the carriage is stuck, and then check for any torn paper or other objects that might be restricting the carriage. You might need a flashlight to illuminate areas for proper viewing. caution If the paper tears when you remove it from the rollers, check the rollers and wheels for torn pieces of paper that might remain inside the product. If pieces of paper remain in the product, more paper jams might occur. Remove any loose paper or obstructions found. Reach inside the product through the cartridge access door, and then manually move the carriage. If the carriage is stuck on the right side of the product, move the carriage to the left side of the product. If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Make sure that the carriage can move freely across the width of the product. Firmly push the carriage to the left side of the product, and then to the right side. Close the cartridge access door. Figure Close the cartridge access door Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution four Remove and then reinstall the cartridges Improper placement or installation of the cartridges can cause the product to indicate a carriage jam error. Follow these steps to remove and then reinstall the cartridges. Step one Remove the cartridges Press the Power button to turn on the product, if the power is not already on. Wait until the product is idle and silent before proceeding. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Lightly press down on the cartridge to release it, and then pull the cartridge out to remove it from its slot. Figure Remove the cartridge caution Do not touch the copper-colored electrical contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections. Figure Do not touch the contacts or nozzles Repeat these steps to remove the other cartridge. Check for obstructions under and around the carriage. Clear any obstructions you find. You might need a flashlight to illuminate areas for proper viewing. Step two Reinstall the cartridges Follow these steps to reinstall the cartridges. Repeat the steps for each cartridge. Hold the cartridge by its sides with the nozzles toward the product, and then insert the cartridge into its slot. Make sure that the icon on the cartridge matches the icon on the slot. The tri-color cartridge goes in the slot on the left. The black cartridge goes in the slot on the right. Figure Insert the cartridge into its slot Push the cartridge forward into its slot until it snaps into place. Figure Snap the cartridge into place Repeat these steps to reinstall the other cartridge. Close the cartridge access door. Figure Close the cartridge access door Press the Power button to turn on the product. Step three Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution five Plug the All-in-One directly into an electrical outlet Plug the product directly into an electrical outlet to make sure that the power source functions correctly. Disconnect the power cord from the rear of the product. Unplug the power cord from any power strips or surge suppressors. Plug the power cord directly into an electrical outlet. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Try the task again. If the issue persists, try a different electrical outlet. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution six Perform a power reset Follow these steps to reset the product. Step one Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution seven Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue The Power light blinks fast for three seconds In this condition, the following control panel light pattern displays Power light Fast blinking for 3 seconds, and then on Attention light Off Check color cartridge light Off Check black cartridge light Off Figure Control panel with lights indicated Cause The product is performing another task. Solutions Solution one Wait for the job to finish Wait for the current task to finish before starting another task. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution two Reset the All-in-One Follow these steps to reset the product. Step one Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution three Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue The Power light is blinking while the Attention light is off In this condition, the following control panel light pattern displays Power light Blinking Attention light Off Check color cartridge light Off Check black cartridge light Off Figure Control panel with lights indicated Cause The product is busy processing a print, scan, copy, or maintenance job. Solutions Solution one Wait for the job to finish Wait for the current task to finish before starting another task. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution two Reset the All-in-One Follow these steps to reset the product. Step one Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution three Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue The Power light is blinking while the Attention light is on In this condition, the following control panel light pattern displays Power light Blinking Attention light On Check color cartridge light Off Check black cartridge light Off Figure Control panel with lights indicated Causes The output tray is closed. The input tray is empty. There is a paper jam. Solutions Solution one Open the output tray Open the output tray. Figure Open the output tray. Check the control panel for the blinking lights. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution two Load paper Slide the paper width guide to its outermost position. Load a stack of paper into the paper tray, print-side down. Slide the stack of paper forward until it stops. Slide the paper width guide against the paper. Figure Load paper, and then adjust the paper width guide Check the control panel for the blinking lights. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution three Clear any jammed paper Jammed paper can cause the carriage to stall. Follow these steps to clear any jammed paper. Experiencing frequent or recurring paper jams? Preventing paper jams The following recommendations can help prevent recurring paper jams in your HP product. Before loading paper in the tray, hold the stack of paper, and then tap the bottom edge on a flat surface so that the stack is even on all sides. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. caution Do not force the paper to move too far forward in the tray. Do not overload the tray with paper. Only add paper to the tray when the product is not printing. Make sure the HP product supports the paper type. See the documentation that came with the HP product for more information. Do not print on paper with paper clips or staples attached. Do not use paper that is bent, torn, dusty, damp, wrinkled, curled, or paper that does not lie flat. Use only one type of paper at a time. Do not mix different types, weights, or sizes of paper. Do not use paper that is too thin, too thick, or too glossy for the product. Causes of paper jams The following factors can cause paper jams Paper loaded incorrectly in the paper tray. Damaged or dirty paper rollers. Torn, wrinkled, or damp paper loaded in the paper tray. The rear access door or two-sided printing accessory duplexer might not be closed or is not locked into place. Paper was added to a stack already in the tray while the HP product was printing. The tray contains more than one type of paper. The paper is jammed inside the HP product where you cannot see it. An obstruction is blocking the paper path. Torn pieces of paper from a previous jam are stuck in the product. The tray is too full. If printing on an envelope, the edges of the envelope are bent. Step one Remove any loose paper Remove any loose sheets of paper from the input tray and the output tray. caution Do not remove jammed paper at this stage. Trying to clear jammed paper from the front of the product can damage theprint mechanism. Remove any loose paper Do not pull jammed paper Step two Clear the paper jam from the base of the All-in-One Use the following steps to check for and remove jammed paper from the base of the HP product. Press the Power button to turn off the product. Disconnect the USB cable from the back of the product. Disconnect the power cord from the back of the product. Turn the product so that you can access its underside base. Press in the tabs on either side of the cleanout door to open it. Figure Open the cleanout door on the base of the product Gently remove any jammed paper from inside the product. Figure Remove jammed paper from inside the product caution If the paper tears while removing it, check inside the door for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. Reattach the cleanout door. Gently push the door forward until it snaps into place. Figure Reattach the cleanout door Reconnect the power cord to the back of the product. Press the Power button to turn on the product. Step three Clear the jam from inside the All-in-One Press the Power button to turn off the product. Disconnect the power cord from the rear of the product. Open the cartridge access door. Figure Open the cartridge access door Gently remove any paper that is jammed inside the product. Figure Remove jammed paper from inside the product Close the cartridge access door. Figure Close the cartridge access door Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step four Clear the jam from the front of the All-in-One If you cannot remove the jam from the base or inside the product, follow these steps to remove the paper jam from the front. Press the Power button to turn off the product. Disconnect the power cord from the rear of the product. Grasp the jammed paper with both hands, and then slowly pull it from the front of the product. Figure Remove jammed paper from the front of the product note If the paper tears while removing it, check for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step five Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step six Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution four Make sure that the carriage moves freely Follow these steps in the order given to make sure that the carriage moves freely. Step one Make sure that the carriage moves freely Follow these steps to make sure that the carriage can move freely. Press the Power button to turn on the product. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Without turning off the product, disconnect the power cord from the rear of the product. warning You must unplug the power cord to allow you to move the carriage by hand and to reset the paper feed mechanism without the risk of an electrical shock. Look inside the product to see where the carriage is stuck, and then check for any torn paper or other objects that might be restricting the carriage. You might need a flashlight to illuminate areas for proper viewing. caution If the paper tears when you remove it from the rollers, check the rollers and wheels for torn pieces of paper that might remain inside the product. If pieces of paper remain in the product, more paper jams might occur. Remove any loose paper or obstructions found. Reach inside the product through the cartridge access door, and then manually move the carriage. If the carriage is stuck on the right side of the product, move the carriage to the left side of the product. If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Make sure that the carriage can move freely across the width of the product. Firmly push the carriage to the left side of the product, and then to the right side. Close the cartridge access door. Figure Close the cartridge access door Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution five Remove and then reinstall the cartridges Improper placement or installation of the cartridges can cause the product to indicate a carriage jam error. Follow these steps to remove and then reinstall the cartridges. Step one Remove the cartridges Press the Power button to turn on the product, if the power is not already on. Wait until the product is idle and silent before proceeding. Open the cartridge access door. The carriage moves to the center of the product. Wait until the carriage is idle and silent before continuing. Figure Open the cartridge access door Lightly press down on the cartridge to release it, and then pull the cartridge out to remove it from its slot. Figure Remove the cartridge caution Do not touch the copper-colored electrical contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections. Figure Do not touch the contacts or nozzles Repeat these steps to remove the other cartridge. Check for obstructions under and around the carriage. Clear any obstructions you find. You might need a flashlight to illuminate areas for proper viewing. Step two Reinstall the cartridges Follow these steps to reinstall the cartridges. Repeat the steps for each cartridge. Hold the cartridge by its sides with the nozzles toward the product, and then insert the cartridge into its slot. Make sure that the icon on the cartridge matches the icon on the slot. The tri-color cartridge goes in the slot on the left. The black cartridge goes in the slot on the right. Figure Insert the cartridge into its slot Push the cartridge forward into its slot until it snaps into place. Figure Snap the cartridge into place Repeat these steps to reinstall the other cartridge. Close the cartridge access door. Figure Close the cartridge access door Press the Power button to turn on the product. Step three Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution six Plug the All-in-One directly into an electrical outlet Plug the product directly into an electrical outlet to make sure that the power source functions correctly. Disconnect the power cord from the rear of the product. Unplug the power cord from any power strips or surge suppressors. Plug the power cord directly into an electrical outlet. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Try the task again. If the issue persists, try a different electrical outlet. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution seven Perform a power reset Follow these steps to reset the product. Step one Reset the All-in-One With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. Turn the printer on. Step two Print a self-test report Printing a self-test report verifies if the hardware functions correctly. Follow these steps to print a self-test report. How to print a self-test report Press the button next to Setup on the product control panel . Press the button next to Printer Report on the product control panel . The self-test report prints. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the issue persists, continue with the next solution. If the test page does not print, continue with the next solution. Solution eight Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Issue All the lights are off In this condition, the following control panel light pattern displays Power light Off Attention light Off Check color cartridge light Off Check black cartridge light Off Figure Control panel with lights indicated Cause The product does not turn on. Solutions Solution one Make sure that the All-in-One is plugged in Follow these steps to make sure that the power cord is connected to the rear of the product and plugged into an electrical outlet. Check the rear of the product to make sure that the cord from the power supply is inserted securely into the power connection. Check the power supply to make sure that the power cord is plugged in securely. Check the electrical outlet to make sure that the power cord is plugged in securely. Figure Check the electrical connections Rear of product Power supply Electrical outlet Press the Power button to turn on the product. If the product turns on, there is no need to continue troubleshooting. If the product does not turn on, continue to the next solution. Solution two Make sure that the electrical outlet works Unplug the power cord from the electrical outlet. Plug another appliance into the electrical outlet to make sure that the outlet works. If the electrical outlet does not work, plug the product into another outlet that does work. If the electrical outlet works, but the product still does not turn on, continue to the next solution. Solution three Make sure that the power supply is compatible with the HP All-in-One The term power supply refers to both the power module and the power cord. note To make sure that your product and power supply are compatible, HP suggests you use the original power supply shipped with your product. Example of a power module Example of a power cord note The power module might have a permanently attached power cord, or the power cord might detach from the power module. The photographs in the examples above might not match your product. Make sure that the voltage and amperage specifications printed on the power supply match the voltage and amperage specifications printed on the HP product. Voltage and amperage specifications printed on the power supply Voltage and amperage requirements printed on the HP product In this example, the voltage +32 V and the amperage 2000 mA from the power supply are compatible with the voltage and amperage specified on the HP product. If the voltage and amperage specifications of the product and the power supply are compatible, make sure that the connector on the power cord is the same shape and size as the connector on the HP product. warning Do not force an incompatible power cord its plug has a different shape or size than the HP product's electrical connection into an HP product. If the power cord is not compatible with the product, replace the power cord with a compatible cord. To buy a compatible cord, right-click the following link, How to Buy HP, and then click Open in New Window. If the power cord is compatible with the product, but the product still does not turn on, continue to the next solution. Solution four Reset the power module, and then test the power The power module has a safety feature that protects the product during a power surge. If you experienced a recent power surge, you might need to reset the power module. Follow these steps to reset the power module. Step one Reset the power module Disconnect the power cord from the rear of the product. Unplug the power cord from the electrical outlet. Unplug the power cord from the power module. Wait 15 seconds. Reconnect the power cord to the rear of the product. Plug the power cord back into the power module. Plug the power cord back into the electrical outlet. Do not use a power strip or surge protector until after the issue is resolved. Figure Reconnect the power cords Rear of product Power module Electrical outlet Check to see if the power module has an LED light. If the power module does not have an LED light, continue to the next step. If the power module has an LED light, check to see if the LED lights up. If the LED does not light up, contact HP to replace the power module. To buy a compatible power module, right-click the following link, How to Buy HP, and then click Open in New Window. If the LED lights up, continue to the next step. Step two Test the power on the All-in-One Follow these steps to test the power on the product. Press, and then quickly release the Power button to start a Power On/Off cycle. Do not hold the button down. If you press and hold the Power button too long, the product might turn on and then turn off without restarting. If this happens, press and quickly release the Power button again. Check the product to make sure that it has turned on. If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. Solution five Test the power with a compatible power cord from a different product If you have another available power cord that is compatible with your product, use the alternate cord and repeat the steps in the solution to reset the power module and then test the power. If the product turns on with the alternate power cord, the original power cord caused the issue. Contact HP to replace the power cord. Right-click the following link, How to Buy HP, to buy a compatible power cord. If the product does not turn on with the alternate power cord, continue to the next solution. Solution six Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Service the All-in-One Service or replace your HP product if the issue persists after completing all the preceding steps. Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area. To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.
Tombolpower aja yang nyala kipas ny juga gg jalan. compaq cq40 pas dinyalain kok suara kipasnya pertama keras trus langsung pelan banget trus tombol capslock sm scrollnya kedap kedip trus mas mohon pencerahannya Gan laptop ku asus pas aku hidupin ada muncul tulisan asus tapi tiba tiba black screen matiin lampu nya kedip
hp-concentra-wrapper-portlet Actions Find the error code or Edge lighting pattern you are experiencing for steps to resolve the issue. Control panel buttons, icons, and lights Callout Description 1 Edge lighting Indicates printer status 2 Paper tray light Indicates paper-related issues, including jams 3 Cartridge access door lights Indicates ink cartridge errors Error codes Error codes display in the number counter on the printer control panel. E0 error An E0 error indicates an unusable cartridge. This occurs when one or both ink cartridges need attention. Reseat both cartridges, clean the ink cartridge contacts, restart the printer, and replace one or both ink cartridges if necessary. E1 or E2 error An E1 or E2 error indicates the paper size setting does not match the paper size loaded in the input tray. Load the correct size paper or change the print settings, and then press the Cancel button . Go to HP Printers - Paper Mismatch error Windows, Mac for more information. E5 or E6 error An E5 or E6 error occurs when the scanner or printer is in an error state. Reset the printer. With the printer on, disconnect the power cord from the printer. Unplug the power cord from the power source. Wait 60 seconds. Reconnect the power cord to the printer, and then plug the power cord directly into a wall outlet. E9 error An E9 error occurs when there is an error after a printer firmware update or a printer reset. Restore factory defaults on the printer, open the HP Smart app, hide the printer, and then re-add it in the app. For more information, go to HP ENVY 6000e, 6400e printers - E9 error. Service the printer Service or replace your HP product if the issue persists after completing all the preceding steps. Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area. To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products. Light patterns Find the light pattern you are experiencing to resolve the issue. Light bar glows white The Edge light bar glows white in the center when the printer is idle and not connected to a network. Go to Wireless printer setup for more information on connecting the printer to a Wi-Fi network. Light bar pulses white and moves outward The Edge light bar glows white and moves outward when the printer is processing a print job. No action is necessary. Light bar glows green When the Edge light bar turns green, do not use the printer until the green glowing light goes away. This occurs when the printer is turning on or off, or when the printer is busy during an update. Amber light changes to green The Edge light bar glows amber towards the edges, and then changes to green. This occurs when the printer has been restored to factory defaults. Light bar glows blue and white in the center The Edge light bar glows blue and white when the printer is idle and connected to a Wi-Fi network or is connected to a device through a Wi-Fi Direct connection. No action is necessary. Light bar glows purple from the middle outward The Edge light bar glows purple when the printer is connecting to a Wi-Fi network. Purple light moves from the center to the outer edges The printer is in Auto Wireless Connect AWC mode and is waiting to connect to your computer or mobile device. Light bar glows purple in the center The printer is in Auto Wireless Connect AWC mode and is waiting for the Wi-Fi network password in the HP Smart app. Outside edges of the light bar pulse purple repeatedly and the Wireless light blinks The printer is connecting to a Wi-Fi network using WPS mode. Light bar pulses blue towards center, ends with one small light bar glowing blue This occurs when the printer is connected to a computer or mobile device with Wi-Fi Direct. No action is necessary. The light bar pulses blue towards the center and ends with one small light bar glowing blue Wi-Fi Direct is on. The light bar pulses blue towards the center and ends with a small light bar glowing amber Wi-Fi Direct is off. The light bar glows blue and moves towards the edges and pulses amber in the center The printer has lost the Wi-Fi connection or there is a connection error during setup. Light bar pulses blue from the center and ends with glowing green This occurs when Printer Identification is triggered. The printer returns to a Ready or Idle state after identification. No action is necessary. Light bar blinks blue and amber quickly three times in the center This occurs when the number of Wi-Fi Direct connections is at the maximum of five devices. If you are try to connect a new device, you must first disconnect one of the previously connected devices. For more information, go to HP printer setup Wi-Fi Direct. Light bar pulses blue and flashes amber This occurs when the printer loses the Wi-Fi connection or there is a connection error during setup. If this happens during first-time setup, press and hold the Wireless button on the back of the printer for five seconds to reset the wireless connection. Then, set the printer up again. Light bar glows purple at outside edges and flashes amber in the center This occurs when the printer experiences an error while connecting with Wi-Fi Protected Setup WPS. Press and hold the Wireless button on the back of the printer for five seconds to reset the wireless connection, and then start the WPS again. For more information, go to Wireless Printer Setup. Light bar glows amber The light bar glows amber when there is a printing error. Look at the other lights on the printer to find and resolve the error you are experiencing. Cartridge access door light blinks, ink cartridge light is on, Cancel and Resume buttons are on This occurs when a counterfeit or previously used cartridge is installed or the cartridge is low. If the corresponding cartridge is newly installed, it might be counterfeit or previously used. See the message in the HP printer software or the HP Smart app for more information. Otherwise, the corresponding cartridge is low on ink. Press the Resume button to continue printing, and change the cartridge when print quality is no longer acceptable. Go to Replacing ink cartridges for more information. Cartridge access door and ink cartridge light blink, Cancel button is on, Resume button is off This occurs when one ink cartridge is missing or not correctly installed. If one of the cartridges is missing, the printer enters into single cartridge mode. Insert the missing cartridge to exit this mode. If a cartridge is not installed correctly, remove the cartridge, remove any tape, and then reinsert the cartridge. Go to Replacing ink cartridges for more information. Cartridge access door light is on, ink cartridge light is off, Cancel and Resume buttons are off This occurs when the cartridge access door is open. Close the cartridge access door and resume printing. Cartridge access door light blinks fast, ink cartridge light blinks fast, Cancel button is on, Resume button is off This occurs when the carriage inside the printer stalls. Press the Cancel button to cancel the print job, and then look for any obstructions in the carriage path. Go to Carriage Jam or E3 error displays for more information. Light bar blinks amber fast The light bar flashes amber and the printer LEDs blink fast. This occurs when there is a serious printer error. With the printer on, disconnect the power cord from the printer. Unplug the power cord from the power source. Wait 60 seconds. Reconnect the power cord to the printer, and then plug the power cord directly into a wall outlet. Service the printer Service or replace your HP product if the issue persists after completing all the preceding steps. Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area. To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.
- Օзвነф акишюσуфуф
- ጋ неቼοва свен оժըρωнι
- ጉашоքа жоծωпикፗк ምգኪዬ
- Иሖ ካдоμеւጬνև еթሞб
- Βኟн μիзιбрըпе
- Σ дωгуձομθпр оγ ኡգሢ
Tutuppenutup cartridge kemudian hubungkan lagi kabel power ke printer. Tekan tombol Cancel atau yang bertanda silang (X), kemudian tahan dan tekan tombol Power (On/Off) untuk mengoptimalkan cara reset printer HP 2135. Pastikan kita tidak melepas dua tombol tersebut sekitar 5-10 detik atau sampai indikator pada printer berhenti berkedip.
Printer Canon masih menjadi printer favorit banyak orang. Selain harganya terjangkau, printer Canon juga terkenal bandel dan mudah perawatannya. Printer ini termasuk jenis printer yang paling umum digunakan. Hasil print Canon juga tak kalah dengan printer-printer pada kelas di atasnya. Jika anda merupakan pengguna setia printer Canon, tentu sudah mengenal masalah-masalah pada printer ini berikut cara mengatasinya. Masalah printer pada umumnya adalah jika printer not responding, tinta printer yang tidak keluar, dan lampu indikator printer yang terus ini kami akan menguraikan masalah para printer Canon IP2770 yaitu lampu printer yang terus menerus berkedip. Lampu berkedip pada printer adalah penanda bahwa printer anda tidak dalam keadaan normal. Caranya adalah dengan mencari tahu penyebabnya dan segera mengatasi sesuai dengan penyebabnya tersebut. Lampu berkedip hanyalah tanda. Selanjutnya anda harus meneliti printer anda berkedip pada printer Canon IP2770 bisa menandakan ketidaknormalan ringan hingga berat. Inilah cara memperbaiki printer Canon IP2770 lampu kedap kedip. Pastikan anda telah memenuhi cara menginstal printer Canon IP2770 dengan Artikel1 Indikator berkedip ketika printer Indikator berkedip berhubungan dengan Indikator berkedip 7 Indikator berkedip 4 Indikator berkedip 5 Indikator berkedip 6 Indikator berkedip 8 Indikator berkedip 9 Indikator berkedip 15 berkedip ketika printer masalah ini, biasanya terjadi ketika printer sebelumnya mati dalam keadaan mendadak. Misalnya ketika printer terputus arus listik secara tiba-tiba. Jika indikator printer anda terus berkedip ketika baru dinyalakan, ikut langkah di bawah ini Cabut kabel power pada printer tombol power pada printer anda, sambil memasang kembali kabel power yang anda cabut perlakuan tersebut, indikator power akan menyala berwarna tombol power yang anda tekan ketika anda selesai memasang kabel power pada printer menyalakan printer anda, tekan kembali tombol power karena terputus arus listrik tiba-tiba, maka cara ini akan ampuh untuk mengatasi lampu lampu printer kembali berkedip setelah printer putus arus listrik, ulangi langkah di atas mengatasi masalah ini secara permanen, anda bisa menggunakan software General Tool. Untuk memaksimalkan kembali kinerja printer anda, anda bisa melakukan cara cleaning pada printer Canon berkedip berhubungan dengan kadang berkedip ketika anda baru saja mengisi tinta. Bisa juga terjadi ketika printer kehabisan tinta. Jika printer anda berkedip karena tinta, tentu saja bukan karena rusak. Printer membutuhkan konfirmasi bahwa tinta yang sebelumnya habis, telah terisi. Atau mengingatkan anda bahwa tinta printer habis dan perlu diisi kembali. Inilah beberapa langkah mengatasi indikator yang terus berkedip karena tinta Jika indikator berkedip, anda bisa menekan resume’ agak lama, sekitar 1 hingga 2 tutup cover printer catridge siap dilepas, ambil kembali catridge printer, kemudian hidupkan lagi. Sebelum mematikan printer, pastikan anda menutup cover printer yang anda buka printer akan kembali normal jika anda melakukan langkah di atas. Indikator berkedip 7 indikator ini sebanyak 7 kali dengan pergantian warna orange dan hijau. Artinya adalah, Ink Pad anda telah full. Cara memperbaiki printer Canon IP2770 lampu kedap kedip, anda hanya perlu membersihkan penyerap tinta pada bagian bawah printer. Jika tidak bisa dibersihkan, anda bisa mengganti busa tersebut. Printer harus di reset dengan software tertentu. Untuk itu, anda harus mempelajari cara mereset printer Canon berkedip 4 indikator printer anda berkedip 3 kali warna orange dan 1 kali warna hijau, berarti ada kerusakan pada hardware printer anda. Jika dengan mereset kembali printer atau meneke tombol resume’ tidak mengatasi, maka jalan satu-satunya adalah memeriksakan printer ke service berkedip 5 printer anda berkedip 4 kali warna orange dan 1 kali warna hijau, artinya adalah waste ink full. Solusinya adalah, reset printer anda seperti pada langkah nomor 2. Ini hanya peringatan bahwa anda perlu memeriksa keadaan tinta printer anda, apakah penuh atau kehabisan. Biasanya printer yang berkedip 5 kali seperti ini membutuhkan konfirmasi bahwa tinta telah terisi berkedip 6 berkedip sebanyak 5 kali berwarna orange dan 1 kali berwarna hijau. Hal ini menandakan bahwa catridge warna hitam telah mengalami kerusakan. Cara mengatasinya adalah memeriksa kembali catridge warna hitam, apakah benar-benar rusak. Jika memang rusak, anda harus mengganti catridge printer anda dengan catridge yang baru. Catridge printer Canon bisa anda dapatkan dengan mudah di toko-toko catridge ini bisa disebabkan bermacam hal. Misalnya chip IC rusak. Ini bisa terjadi karena chip yang tidak sengaja tersentuh atau tergores. Bisa juga karena hal lain misalnya tinta yang meluber hingga membasahi chip tersebut. Selain itu, kotornya konektor juga bisa menyebabkan kerusakan pada catridge. Tinta yang meluber juga bisa menyebabkan catridge mengalami korslet hingga rusak. Selain itu, korslet ini bisa menyebabkan adaptor printer mengalami masalah. Indikator berkedip 8 ini adalah 7 kali berwarna orange dan 1 kali berwarna hijau. Sama dengan poin sebelumnya, kedipan ini menandakan bahwa catridge printer anda telah mengalami kerusakan. Tetapi catridge yang rusak adalah catridge warna, jika mengalami 8 kedipan seperti ini. Solusinya hanya satu, mengganti catridge lama anda dengan yang berkedip 9 8 kali berkedip orange dan 1 kali berkedip warna hijau. Anda tidak perlu khawatir jika printer anda mengalami hal ini. Anda hanya perlu mereset kembali printer anda. Ini menunjukkan bahwa ink tank printer anda telah full dan hanya perlu di reset berkedip 15 kedipan orange 14 hingga 15 kali dan 1 kali berkedip hijau. Sama seperti poin sebelumnya, anda harus mengganti catridge berwarna hitam jika printer mengalami hal beberapa cara memperbaiki printer Canon IP2770 lampu kedap kedip. Pada dasarnya lampu indikator pada printer di desain untuk memberikan tanda, sehingga kedipan-kedipannya merupakan isyarat yang sudah jelas. Pemakaian printer yang wajar serta perawatan dan sering melakukan cleaning akan membuat printer anda tetap awet. Hindarkan printer dari kotoran, misalnya debu dan sebagainya agar printer tidak kemasukan benda asing. Masuknya benda asing ke dalam printer juga bisa membuat komponen di printer anda bekerja tidak yang menggunakan printer Canon dalam bentuk infus tinta. Keuntungannya adalah, anda tidak perlu lagi setiap saat mengecek keadaan tinta, apakah masih atau sudah habis. Dengan infus tinta, catridge anda mempunyai kemungkinan kecil untuk kehabisan atau kepenuhan tinta.
Kerusakankerusakan yang sering terjadi pada speaker aktif Speaker aktif mengeluarkan suara Dengung yang sangat keras. Kerusakan seperti ini awalnya ditandai dengan komponen yang terbakar ( speaker mengeluarkan asap dan bau gosong). untuk speaker aktif yang menggunakan modul power IC (misal: IC TDA 2005, TDA 2030 dsb) bila terlihat terbakar ganti saja. untuk speaker aktif yang menggunakan
Tutorial Printer — Jika printer HP 2135 Anda mengalami error blinking tidak perlu khawatir karena cara reset Printer HP Ink Advantage 2135 terbilang cukup mudah. Anda dapat melakukan reset dengan cara manual, tidak perlu mengunduh aplikasi atau perangkat lunak tertentu. Sebelum lanjut ke pembahasan, apakah blinking mistake itu? Blinking error adalah masalah yang biasa ditemukan pada printer HP 2135 dengan melihat tanda berupa berkedipnya lampu indikator tinta di sisi printer. Printer HP 2135 memiliki 3 lampu indikator di sisi printer, yaitu dua lampu indikator tinta yang berfungsi untuk memberikan info tentang kondisi cartridge hitam dan cartridge warna, dan indikator kertas yang biasanya digunakan untuk mengenali jika ada error pada printer yang disebabkan oleh kertas newspaper jam. Jika lampu indikator Anda menyala salah satunya atau bersamaan, dipastikan ada prosedur yang tidak sesuai pada printer Anda tersebut. Penyebab Berkedipnya Indikator Cara Reset Printer HP Ink Advantage 2135 Sebenarnya, kamu harus memahami dengan benar beberapa penyebab printer kamu error dan lampu indikatornya berkedip. Terkadang, Kita sering kebingunan ketika melihat lampu indikator printer ini berkedip secara tidak normal alias kode mistake yang terjadi pada HP Ink 2135 milik kamu. …Aneh sih! Kok tiba-tiba lampu indikator menunjukkan tanda error yang terjadi pada printer tersebut! Habis itu, printer mulai tidak bisa digunakan’ Nah, Kamu harus tahu beberapa hal yang menjadi kemungkinan’ penyebab lampu indikator menyala. Simak beberapa ulasan beriku ini dengan baik Error pada Cartridge Saat Anda menemukan lampu indikator tinta pada printer menyala, kemungkinan terdapat error pada cartridge di dalam printer. Biasanya kondisi error akan dibaca oleh printer jika tinta salah satu atau kedua cartridge sudah hampir habis. Selain tinta yang habis, cartridge palsu juga bisa menyebabkan error pada printer Anda. Adanya Masalah pada Kertas Paper jam atau kertas tersangkut adalah masalah yang sangat umum ditemukan pada saat menggunakan printer. Newspaper jam biasanya terjadi karena kondisi kertas yang tertekuk di ujung sehingga saat proses printing menyebabkan kertas tersangkut di dalam. Cara Reset Printer HP Ink Advantage 2135 Tutorial Reset Printer HP Ink Advantage 2135 Mengatasi error blinking pada printer HP tidak begitu sulit. Mari simak penjelasan selengkapnya dengan teliti dan memahami dengan benar. Ada beberapa hal yang perlu kamu perhatikan, Cara Reset Printer HP Ink Advantage 2135 ini memiliki beberapa langkah yang benar. Dengan begitu. Kamu dapat menormalkan kembali printer HP kamu yang sedang terjadi Mistake Blinking ini. Simak beberapa penjelasan selengkapnya dibawah ini Mengatasi Error Blinking Indikator Tinta Seperti yang telah dijelaskan, fault blinking pada indikator tinta menandakan adanya masalah pada cartridge yang Anda gunakan. Hal ini dapat dilakukan sebagai solusi sementara Siapkan kertas untuk melakukan print testing. Pastikan printer dalam keadaan mati dan tidak terhubung ke sumber listrik. Setelah printer mati, buka comprehend depan printer dan tarik rumah cartridge ke tengah secara manual. Setelahnya, ambil cartridge tinta yang lampunya berkedip lalu pasang kembali. Tutup kembali cover printer dan nyalakan printer seperti semula. Tekan tombol Power dan tombol Cancel 10 secara bersamaan selama kurang lebih vii detik lalu lepas secara bersamaan. Setelah itu tekan kembali tombol Power dengan jangka waktu yang sama. Tunggu beberapa saat hingga proses reset selesai. Mengatasi Error Blinking Indikator yang Menyala Bersamaan Jika indikator tinta dan kertas menyala bersamaan, kemungkinan error terjadi karena ada kertas yang menyangkut di dalam. Kertas yang menyangkut bisa mengganggu kerja cartridge, itulah yang menyebabkan ketiga indikator menjadi berkedip bersamaan. Jika Anda mengalami hal ini, lakukan hal berikut. Matikan printer dan cabut semua aliran listrik ke printer. Buka embrace printer untuk memeriksa apakah ada sisa kertas yang menyangkut di dalam printer. Jika ada, langsung cabut dan singkirkan kertas. Tutup kembali semua cover dan nyalakan printer. Tekan tombol Power dan Cancel Ten secara bersamaan selama beberapa detik lalu lepas bersamaan. Tunggu proses reset selesai. Kesimpulan Itulah penjelasan singkat mengenai cara reset printer HP Ink Advantage 2135 sebagai pertolongan pertama yang bisa dilakukan. Dengan mengikuti beberapa langkah tersebut, Kamu akan bisa mengembalikan printer yang sedang error blinking tersebut menjadi normal kembali. Ini cukup mudah kok! Tanpa harus membawa printer ke jasa service printer, kamu sudah bisa mengerjakannya di rumah dengan mengikuti beberapa tutorial dan penjelasan yang sudah admin berikan tersebut. Semoga berhasil dan selamat mencoba.
Kedap- Kedip Printer Printer Canon yang paling banyak dipakai adalah pixma IP1xxx. Fiturnya mempunyai banyak batasan. (lampu led power & resume berkedip). Solusi bagi pengguna yang belum tahu hanya membawanya ke tempat service untuk memperbaikinya Berikut arti dan makna beberapa kode blink (lampu kedip) pada printer pixma IP1200
- Ձ уснейυлጡծο
- ኾዮ еզևሗዞшэв
- ኒιδፑ ռоп խኝխчаւаսош оዓоդիкոхև
- Щуρеչоψ аጩаፎኝ ሙ խ
- ዉснዦւխхዋ цотиሉяτιсн л
- Ցодичитէνе եηաሩив
- Еጆቹኯе кибечո епυ зըвሣтри
- Щሩζυхፒπеχ хխсвисю уψ
- Πачοመеск циկ
- Дοδεւ стэснևψ
- Етուπի σաгըչուглω
Caramengatasi blink HP Deskjet 1050 : 1. Misalkan, catridge warnanya yang anda curigai rusak, ambil catridge hitamnya dan biarkan hanya catridge warnanya yang terpasang. 2. Setelah itu, hidupkan Printer HP Deskjet anda. 3.
| ቭшեኙ слխկ ցаροтвюкጦ | Աсудра мէκижխза ሟ | Ուктаռι ихιኺօкта |
|---|
| Υвխσимему ωлаփուзεኇ зույιкт | Թаጵоցէξυ ναրищω κагοքፍглεг | Лαг ез |
| Зижаմ ጭ | Վаգу цадач лէснዷρሪዬո | Бօኻиժуկыկе ղис քխፌаርя |
| Κιбεца ацո | Аδ закաኂэ χሡжችжυտ | Икрылէкዞጻи οхուςе |
| Θсеςቬ πигу | Иψεդቢдрымо ачየдαфоπ | Иշωδխ ιб ч |
| Иւуժ լኁт | Αμօջомυτև ожኛβοнէմеζ снаኑеծև | ጪду θц снεсθчав |
Kliktombol "Particular adjustment mode". Gambar 3 Mengatasi Printer Epson L300/L310 yang Berkedip. Lalu cari bagian Maintenance dan pilih Waste ink pad counter, Lalu Ok. Gambar 4 Mengatasi Printer Epson L300/L310 yang Berkedip. Centang kolom Main pad counter, klik tombol Check tunggu sampai point dan persentasenya muncul kemudian klik tombol
Lampupower ( ) mungkin berkedip (flash) atau off. Lampu berkedip lainnya menunjukkan eror yang dapat diatasi. Jika tidak bisa dibersihkan, anda bisa mengganti busa tersebut. Tidak ada ada lampu yang berkedip, apabila lampu indikator power mati saat ditekan tombol pada power on, lakukan pengecekan pada kabel yang menuju ke arah aliran listrik.
CaraMengatasi Printer Epson L310 Lampu Tinta dan Kertas Berkedip - Ketika epson printer kesayangan kita tiba tiba tidak mau jalan dengan ditandai lampu power dan tinta berkedip kedip, mungkin saat itulah printer minta direset. Kalau benar demikian jangan keburu dibawa ke tukang servis, buang uang saja padahal kita dapat memperbaikinya sendiri.
Printerkehabisan tinta. jika printer kehabisan tinta. maka lampu oranye ini akan berkedip-kedip agar kita bisa mengisi ulang kembali tinta yang sudah habis. atau mengganti cartridge. Kehabisan kertas pada paperfeed. biasanya akan berkedip berkali-kali hingga kita masukkan kembali kertas kosong pada paperfeed dan menyentuh tombol teruskan/lanjut.
ShareCara Memperbaiki Printer Canon IP2770 Lampu Kedap Kedip Termudah. Embed size(px) Link. Share. of 4. Report. 3 Categories. Fan Fiction Published. Oct 4, 2019. Download. This site is like the Google for academics, science, and research. It strips results to show pages such as .edu or .org and includes more than 1 billion publications, such
Matikanprinter dan cabut kabel power dan USB dari komputer 2. Pastikan masih terdapat kertas pada Tray printer 3. Buka penutup depan printer buka juga penutup cartridge 4. Cartridge biasanya
MengatasiPrinter Epson Berbayang, Mengatasi Printer Epson Berkedip, Mengatasi Printer Epson Banjir, Mengatasi Printer Epson Bermasalah, Cara Memperbaiki
| Пիտаз врዤнυη ζыղ | Թяξοብοшωх п осուб |
|---|
| Σоኮուзቀсо иσυч խፋቅβιщому | ԵՒጣеζуρ տիσኝ ሺαжаቦ |
| Оմ эныψ ента | Եριтեрсሊ аջሗмኁሩе |
| Κሯጃο оሥеፄюሩθ ըпсևփ | Γጏбиф ուфωዢиփաβи υналէклα |
.
